Miniature Bearings Australia Pty Ltd

Spur gear stock metric categories


Gears Metric Spur


Gears - Spur - Module 0.4 - Brass
Gears - Spur - Module 0.4 - Brass

Also see combined categories:
All Module 0.4 Spur Gears
All Metal Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Brass.

There is also a good range of Gears - Spur - Module 0.4 - Brass on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Plastic
Gears - Spur - Module 0.4 - Plastic

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic.

There is also a good range of Gears - Spur - Module 0.4 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Plastic
Gears - Spur - Module 0.5 - Plastic

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic.

There is also a good range of Gears - Spur - Module 0.5 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Stainless
Gears - Spur - Module 0.5 - Stainless

Also see combined categories:
All Module 0.5 Spur Gears
All Metal Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Stainless.

There is also a good range of Gears - Spur - Module 0.5 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 0.7 - Plastic
Gears - Spur - Module 0.7 - Plastic


PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.7 - Plastic.

There is also a good range of Gears - Spur - Module 0.7 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Aluminium
Gears - Spur - Module 0.8 - Aluminium

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Aluminium.

There is also a good range of Gears - Spur - Module 0.8 - Aluminium on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Plastic
Gears - Spur - Module 0.8 - Plastic

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic.

There is also a good range of Gears - Spur - Module 0.8 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Stainless
Gears - Spur - Module 0.8 - Stainless

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Stainless.

There is also a good range of Gears - Spur - Module 0.8 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 1.25 - Stainless
Gears - Spur - Module 1.25 - Stainless

Also see combined categories:
All Module 1.25 Spur Gears
All Metal Module 1.25 Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.25 - Stainless.

There is also a good range of Gears - Spur - Module 1.25 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 1.5 - Plastic
Gears - Spur - Module 1.5 - Plastic

Also see combined categories:
All Module 1.5 Spur Gears
All Plastic Module 1.5 Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.5 - Plastic.

There is also a good range of Gears - Spur - Module 1.5 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 1 - Plastic
Gears - Spur - Module 1 - Plastic

Also see combined categories:
All Module 1.0 Spur Gears
All Plastic Module 1.0 Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1 - Plastic.

There is also a good range of Gears - Spur - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 3 - Plastic
Gears - Spur - Module 3 - Plastic

Also see combined categories:
All Module 3.0 Spur Gears

PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 3 - Plastic.

There is also a good range of Gears - Spur - Module 3 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Plastic with Insert
Gears - Spur - Module 0.4 - Plastic with Insert

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.4 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Plastic with Insert
Gears - Spur - Module 0.5 - Plastic with Insert

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.5 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Plastic with Insert
Gears - Spur - Module 0.8 - Plastic with Insert

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.8 - Plastic with Insert on the Small Parts and Bearings website.


You may also be interested in

Spur Gear Stock Inch


Gears - Spur - Stock - 24DP - Steel
Gears - Spur - Stock - 24DP - Steel

Also see combined categories:
All Imperial Spur Gear Stock

Lengths of spur gear stock for manufacturing gears. DP stands for Diametrical Pitch and is an imperial measurement system.

24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - Stock - 24DP - Steel.

There is also a good range of Gears - Spur - Stock - 24DP - Steel on the Small Parts and Bearings website.


Gears - Bevel - Module 1.5 - Plastic
Gears - Bevel - Module 1.5 - Plastic

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - Module 1.5 - Plastic.

Related Information:

There is also a good range of Gears - Bevel - Module 1.5 - Plastic on the Small Parts and Bearings website.


Gears - Bevel - Module 1 - Plastic
Gears - Bevel - Module 1 - Plastic

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - Module 1 - Plastic.

Related Information:

There is also a good range of Gears - Bevel - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Mitre - Module 0.5 - Plastic
Gears - Mitre - Module 0.5 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 0.5 - Plastic.

Related Information:

There is also a good range of Gears - Mitre - Module 0.5 - Plastic on the Small Parts and Bearings website.


Gears - Mitre - Module 1.5 - Brass
Gears - Mitre - Module 1.5 - Brass

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1.5 - Brass.

Related Information:

There is also a good range of Gears - Mitre - Module 1.5 - Brass on the Small Parts and Bearings website.


Gears - Mitre - Module 1 - Brass
Gears - Mitre - Module 1 - Brass

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Brass.

Related Information:

There is also a good range of Gears - Mitre - Module 1 - Brass on the Small Parts and Bearings website.


Gears - Mitre - Module 1 - Plastic
Gears - Mitre - Module 1 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Plastic.

Related Information:

There is also a good range of Gears - Mitre - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Mitre - Module 3 - Plastic
Gears - Mitre - Module 3 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 3 - Plastic.

Related Information:

There is also a good range of Gears - Mitre - Module 3 - Plastic on the Small Parts and Bearings website.


Gears - Mitre - Module 1 - Zinc Diecast
Gears - Mitre - Module 1 - Zinc Diecast

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Zinc Diecast.

Related Information:

There is also a good range of Gears - Mitre - Module 1 - Zinc Diecast on the Small Parts and Bearings website.


Gears - Mitre - Module 2 - Zinc Diecast
Gears - Mitre - Module 2 - Zinc Diecast

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 2 - Zinc Diecast.

Related Information:

There is also a good range of Gears - Mitre - Module 2 - Zinc Diecast on the Small Parts and Bearings website.


Gears - Mitre - Spiral - Module 1.5 - Steel
Gears - Mitre - Spiral - Module 1.5 - Steel

Also see combined categories:
All Metric Mitre Gears
All Metric Spiral Mitre Gears

1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.

A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Spiral - Module 1.5 - Steel.

Related Information:

There is also a good range of Gears - Mitre - Spiral - Module 1.5 - Steel on the Small Parts and Bearings website.


Gears - Mitre - Spiral - Module 3.5 - Steel
Gears - Mitre - Spiral - Module 3.5 - Steel

Also see combined categories:
All Metric Mitre Gears
All Metric Spiral Mitre Gears

1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.

A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Spiral - Module 3.5 - Steel.

There is also a good range of Gears - Mitre - Spiral - Module 3.5 - Steel on the Small Parts and Bearings website.


Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand
Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 6.90o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:

There is also a good range of Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand on the Small Parts and Bearings website.


Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:

There is also a good range of Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand on the Small Parts and Bearings website.


Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:

There is also a good range of Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand on the Small Parts and Bearings website.


Belts - Timing - 14.000mm Pitch - GT - 115mm Wide
Belts - Timing - 14.000mm Pitch - GT - 115mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:

There is also a good range of Belts - Timing - 14.000mm Pitch - GT - 115mm Wide on the Small Parts and Bearings website.


Belts - Timing - 14.000mm Pitch - GT - 170mm Wide
Belts - Timing - 14.000mm Pitch - GT - 170mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:

There is also a good range of Belts - Timing - 14.000mm Pitch - GT - 170mm Wide on the Small Parts and Bearings website.


Belts - Timing - 14.000mm Pitch - GT - 40mm Wide
Belts - Timing - 14.000mm Pitch - GT -  40mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:

There is also a good range of Belts - Timing - 14.000mm Pitch - GT - 40mm Wide on the Small Parts and Bearings website.


Belts - Timing - 14.000mm Pitch - GT - 55mm Wide
Belts - Timing - 14.000mm Pitch - GT -  55mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:

There is also a good range of Belts - Timing - 14.000mm Pitch - GT - 55mm Wide on the Small Parts and Bearings website.


Belts - Timing - 14.000mm Pitch - GT - 85mm Wide
Belts - Timing - 14.000mm Pitch - GT -  85mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:

There is also a good range of Belts - Timing - 14.000mm Pitch - GT - 85mm Wide on the Small Parts and Bearings website.


Belts - Timing - 2.000mm Pitch - GT - 4mm Wide
Belts - Timing -  2.000mm Pitch - GT -  4mm Wide

Also see combined categories:
All 2mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 2.000mm.

Related Information:

There is also a good range of Belts - Timing - 2.000mm Pitch - GT - 4mm Wide on the Small Parts and Bearings website.


Belts - Timing - 8.000mm Pitch - GT - 12mm Wide
Belts - Timing -  8.000mm Pitch - GT -  12mm Wide

Also see combined categories:
All 8mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 8.000mm.

Related Information:

There is also a good range of Belts - Timing - 8.000mm Pitch - GT - 12mm Wide on the Small Parts and Bearings website.


Belts - Timing - 8.000mm Pitch - GT - 20mm Wide
Belts - Timing -  8.000mm Pitch - GT -  20mm Wide

Also see combined categories:
All 8mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 8.000mm.

Related Information:

There is also a good range of Belts - Timing - 8.000mm Pitch - GT - 20mm Wide on the Small Parts and Bearings website.


Belts - Timing - 8.000mm Pitch - GT - 30mm Wide
Belts - Timing -  8.000mm Pitch - GT -  30mm Wide

Also see combined categories:
All 8mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 8.000mm.

Related Information:

There is also a good range of Belts - Timing - 8.000mm Pitch - GT - 30mm Wide on the Small Parts and Bearings website.


Belts - Timing - 8.000mm Pitch - GT - 50mm Wide
Belts - Timing -  8.000mm Pitch - GT -  50mm Wide

Also see combined categories:
All 8mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 8.000mm.

Related Information:

There is also a good range of Belts - Timing - 8.000mm Pitch - GT - 50mm Wide on the Small Parts and Bearings website.


Belts - Timing - 8.000mm Pitch - GT - 85mm Wide
Belts - Timing -  8.000mm Pitch - GT -  85mm Wide

Also see combined categories:
All 8mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 8.000mm.

Related Information:

There is also a good range of Belts - Timing - 8.000mm Pitch - GT - 85mm Wide on the Small Parts and Bearings website.


Belts - Timing - 2.000mm Pitch - GT - 3mm Wide
Belts - Timing -  2.000mm Pitch - GT -  3mm Wide

Also see combined categories:
All 2mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 2.000mm.

Related Information:

There is also a good range of Belts - Timing - 2.000mm Pitch - GT - 3mm Wide on the Small Parts and Bearings website.


Belts - Timing - 2.000mm Pitch - GT - 6mm Wide
Belts - Timing -  2.000mm Pitch - GT -  6mm Wide

Also see combined categories:
All 2mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 2.000mm.

Related Information:

There is also a good range of Belts - Timing - 2.000mm Pitch - GT - 6mm Wide on the Small Parts and Bearings website.


Belts - Timing - 2.000mm Pitch - GT - 9mm Wide
Belts - Timing -  2.000mm Pitch - GT -  9mm Wide

Also see combined categories:
All 2mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 2.000mm.

Related Information:

There is also a good range of Belts - Timing - 2.000mm Pitch - GT - 9mm Wide on the Small Parts and Bearings website.


Belts - Timing - 3.000mm Pitch - GT - 15mm Wide
Belts - Timing -  3.000mm Pitch - GT - 15mm Wide

Also see combined categories:
All 3mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 3.000mm.

Related Information:

There is also a good range of Belts - Timing - 3.000mm Pitch - GT - 15mm Wide on the Small Parts and Bearings website.


Belts - Timing - 3.000mm Pitch - GT - 6mm Wide
Belts - Timing -  3.000mm Pitch - GT -  6mm Wide

Also see combined categories:
All 3mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 3.000mm.

Related Information:

There is also a good range of Belts - Timing - 3.000mm Pitch - GT - 6mm Wide on the Small Parts and Bearings website.


Belts - Timing - 3.000mm Pitch - GT - 9mm Wide
Belts - Timing -  3.000mm Pitch - GT -  9mm Wide

Also see combined categories:
All 3mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 3.000mm.

Related Information:

There is also a good range of Belts - Timing - 3.000mm Pitch - GT - 9mm Wide on the Small Parts and Bearings website.


Belts - Timing - 5.000mm Pitch - GT - 15mm Wide
Belts - Timing -  5.000mm Pitch - GT - 15mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.93mm. Belt Height (W) - 3.81mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 5.000mm.

Related Information:

There is also a good range of Belts - Timing - 5.000mm Pitch - GT - 15mm Wide on the Small Parts and Bearings website.


Belts - Timing - 5.000mm Pitch - GT - 9mm Wide
Belts - Timing -  5.000mm Pitch - GT -  9mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.93mm. Belt Height (W) - 3.81mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 5.000mm.

Related Information:

There is also a good range of Belts - Timing - 5.000mm Pitch - GT - 9mm Wide on the Small Parts and Bearings website.


Pulleys - Timing - 2.032mm Pitch - MXL - STOCK - Aluminium
Pulleys - Timing -  2.032mm Pitch - MXL - STOCK - Aluminium

Also see combined categories:
All MXL 2.032mm Pitch Timing Pulleys

For manufacture of timing pulleys or applications requiring multiple belts from a single drive.

2.032mm metric is equivalent to 0.080 pitch imperial. This category may be available in the new MBA online store at Pulleys - Timing - 2.032mm Pitch - MXL - STOCK - Aluminium.

Related Information:

There is also a good range of Pulleys - Timing - 2.032mm Pitch - MXL - STOCK - Aluminium on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 212690 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 212690 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.