Pins Dowel Categories


Category Matches

Pins Dowel

TopHide Pictures

Pins - Dowel Bushings
Pins - Dowel Bushings

Search Rating: 100%

Also see combined categories:
All Dowel Bushings

Series DB100 Spirol

Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel Bushings.

Pins - Dowel - Extractable
Pins - Dowel - Extractable

Search Rating: 100%

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6. Din 7979.

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin to overcome the problem of pressure build up by trapped air. Hardness 55-62 HRC, HV550-650. Extractable pins may or may not have a flat to vent pressure when pulling. Also known as parallel pins.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Extractable.

Pins - Dowel - Extractable - With Vent
Pins - Dowel - Extractable - With Vent

Search Rating: 100%

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6 with a ground flat along one edge

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650. Also known as parallel pins.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Extractable - With Vent.

Pins - Dowel - Standard - 303-304 Stainless - Chamfered End
Pins - Dowel - Standard - 303-304 Stainless - Chamfered End

Search Rating: 100%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 303/304 Grade Stainless - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 303-304 Stainless - Chamfered End.

Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends
Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends

Search Rating: 100%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 303/304 Grade Stainless- DIN7

Rounded end dowel pins are measured from the start of the edge rounding. This allows the pin to completely fill the hole after you grind off the rounded end. Diameter tolerances are m6. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends.

Pins - Dowel - Standard - 316 Stainless - Chamfered End
Pins - Dowel - Standard - 316 Stainless - Chamfered End

Search Rating: 100%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 316 Stainless - Chamfered End.

Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends

Search Rating: 100%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - DIN7

Diameter tolerances are m6. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends.

Pins - Dowel - Standard - 416 Stainless - Chamfered End
Pins - Dowel - Standard - 416 Stainless - Chamfered End

Search Rating: 100%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 416 Grade - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 416 Stainless - Chamfered End.

Pins - Dowel - Standard - Chamfered End
Pins - Dowel - Standard - Chamfered End

Search Rating: 100%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - Chamfered End.

Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends
Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends

Search Rating: 100%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - DIN7

Diameter tolerances are m6. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends.

Pins - Groove
Pins - Groove

Search Rating: 99%

Also see combined categories:
All Groove Pins

Non threaded press fit fastener that doesn't require a reamed hole as do dowel pins.Commonly used in place of taper pins.

An economic method of fastening without the need for precision drilled and reamed holes. Recommended hole tolerance is H11. Total length may be slightly longer than the nominal length. Expanded portion of the pin is compressed into the hole a few thousands of an inch wider than the nominal pin diameter. Radial forces lock the pin securely into the drilled hole.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Groove.

Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Search Rating: 99%

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Hammer Drive - Flat Head.

Pins - Hammer Drive - Round Head - Stainless Steel
Pins - Hammer Drive - Round Head - Stainless Steel

Search Rating: 98%

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Hammer Drive - Round Head - Stainless Steel.

Shafting General Purpose

TopHide Pictures

Rod - Drill Blanks
Rod - Drill Blanks

Search Rating: 55%

Also see combined categories:
All Silver Steel Drill Blanks
All Drill Rod

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Rod - Drill Blanks.

Tools Pullers

TopHide Pictures

Tools - Pullers - Dowel Remover and Setter
Tools - Pullers - Dowel Remover and Setter

Search Rating: 40%

Also see combined categories:
All Tools

Designed for removing and setting any pull dowel up to 25.40mm.

Puller studs are threaded into the pull dowel and puller. Upward hammering motion with the slide handle is used to remove the dowel and a downward motion is used to set.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Tools - Pullers - Dowel Remover and Setter.


Show all items starting with
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   1   2   3   4   5   6   7   8   9  





Other Store Pages

Click Page Banner Below

Top

Main Pages

Click Page Banner Below

Top





Top



Freight Rates
Terms and Conditions
Privacy Policy

Miniature Bearings Australia offers 119835 products in 2828 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.